Haier Washer Dryer HWM90DD User Manual

Haier Washing Machine  
HWM90DD  
 
16. Do not use this appliance for commercial clothes washing.  
17. Do not operate this appliance unless all enclosure panels are  
properly in place.  
18. Do not tamper with controls.  
19. The appliance is not instruct for use of young children of infirm  
persons without supervision. Young children should be supervised  
to ensure that they do not play with the appliance.  
20. This appliance must be connected to a proper electrical outlet with  
the correct electrical supply.  
21. Do not repair or replace any part of the appliance or attempt any  
servicing unless specifically recommended in the user-repair  
instructions. Make sure that you understand and have the skills to  
carry out.  
22. To reduce the risk of electric shock or fire, do not use extension  
cords or adapters to connect the unit to electrical power source.  
23. If the washing machine is connected to a cord extension set or  
electrical portable outlet device, make sure it is not in a position  
where it is subject to splashing or ingress of moisture.  
24. Ensure carpet does not obstruct the opening in the bases.  
25. Use the new hose provided. The old hose should not be reused.  
2
 
TABLE OF CONTENTS  
PAGE  
IMPORTANT SAFETY INSTRUCTIONS..................  
1-2  
OPERATING INSTRUCTIONS...............................  
Parts and Features..................................................  
Operations.............................................................  
Normal Operating Sounds........................................  
Lint Filter ..............................................................  
Install the linner cover.....................................................  
4
4
5
8
9
9
CARE AND CLEANING GUIDE...............................  
Cleaning and Maintenance.....................................  
Moving & Vacationing.............................................  
Storage of Your Washer in Cold Environment..............  
10  
10  
10  
11  
TROUBLE SHOOTING..........................................  
12  
INSTALLATION INSTRUCTIONS...........................  
Tools and Materials Required.................................  
Unpacking Your Washer.........................................  
Leveling Your Washer...........................................  
Steps for Installation.............................................  
14  
14  
15  
15  
16  
ELECTRICAL REQUIREMENTS............................  
Power Interruptions..............................................  
18  
18  
......................................  
Back Cover  
SPECIFICATION  
3
 
OPERATING INSTRUCTIONS  
Parts and Features  
Soak  
Wash  
Rinse  
Spin  
Hot/Cold  
Heavy Duty  
Hand Wash  
Stain Wash  
Heavy  
Normal  
Quick wash  
Warm/Cold  
Cold/Cold  
Whites  
Colors  
Delicate Casual  
Wrinkle Control  
Medium  
Light  
Start  
Pause  
Warm/Warm  
Delay Time  
Estimated Time  
Water  
Signal  
Wash/Rinse  
Power  
On/Off  
Wash  
Speed  
Spin  
Speed  
Extra  
Rinse  
Soil  
Level  
Cycles  
Process  
Delay  
Temp  
Level  
6
1
7
8
12  
2
11  
10  
13  
14  
3
9
4
15  
16  
5
Top lid  
Door switch  
1
2
3
4
7
8
13 Inner tub  
Bleach injection inlet  
14 Paddle  
Control panel  
Control panel seat  
Cabinet  
9 Front door  
15 Pulsator  
Filter, Filter Cover  
Outer tub cover  
10  
11  
16 Drain hose  
joint  
Leveling legs  
Inner cover  
5
6
12 Balance ring  
4
 
Operations  
Heavy Duty  
Soak  
Wash  
Rinse  
Hot/Cold  
Hand Wash  
Stain Wash  
Heavy  
Normal  
Whites  
Colors  
Quick Wash  
Warm/Cold  
Cold/Cold  
Delicate Casual  
Medium  
Light  
Start  
Pause  
Wrinkle Control Spin  
Warm/Warm  
Delay Time  
Estimated Time  
Water  
Wash/Rinse  
Power  
On/Off  
Wash  
Speed  
Spin  
Speed  
Extra  
Rinse  
Soil  
Level  
Cycles  
Signal  
Process  
Delay  
Temp  
Level  
Delay  
When not activated, the display shows cycle remaining time  
through the wash process.  
When delay is selected the indicator light will display a minimum  
delay of 2 hours. Push button once for every additional1hour  
delay for up to 24 hours. Number of hours will reduce until  
program starts.  
Cycles  
Heavy Duty-For washing bigger ,thicker and heavier dirty  
laundries.  
Normal- For washing cottons and linens,Loads that are  
moderately or heavily soiled.  
Whites-For washing the clothes that is not easy to wash and  
need good rinse effection,such as underwear,and children's  
clothes.  
Colors-For washing color fabrics.  
Hand Wash-To have hand wash effect onclothes.  
Quick Wash-For quick washing of light dirty laundries. It need  
24-30 minutes without extra rinse.  
Delicate Casual-For washing of delicate fabrics.  
Wrinkle Control-Helps to reduce wrinkles and easy ironing.  
Process  
This is to select washing process.  
Soak will not work in the Cycles:Hand Wash,Quick Wash,  
Delicate Casual and Wrinkle Control.  
5
 
Water level indicator will shut off if onlySpin is selected.  
Extra Rinse  
Once a program is selected, press this button to have a extra  
rinse.The washer will add a extra rinse.  
Wash Speed/Spin Speed  
For selecting the speed of washing or spinning .  
Water level  
Water levels may be setat the beginningof the washor at pause.  
During Soak, Wash or Rinsepress this buttonto manually  
replenish water. Release to stop. Function automatically is  
inactive when waterreaches the overflowprotection level.  
Signal  
Signal volume can be adjusted softer, louder or off.  
Soil Level  
According toclothes soil level, press this buttonto change  
washing time.  
Wash cycle increases 2minutes for every soil level.  
Temp  
To select inlet water temperature for washand rinse.  
Power On/Off  
Push the Power On/Off button to switch the machine on or off.  
Start/Pause  
Once washer ispowered and selectionsare chosen, pushthis  
button once tostart washing.  
While unit isworking, push thisbutton once topause it.  
If unit isin Pause mode, push this buttononce to resume  
operation.  
Delay Start and Estimated Time Indicator  
Indicates remaining minutes when cycle is in progress.  
6
 
Indicates remaining hoursduring delay process.  
Indicates fault codesor conditions thatare not normal.  
Loading the Washer:  
Load each itemloosely.  
Separate the whiteand colored clothes.Separateheavy clothes  
from light clothes.  
Carefully check allpockets and cuffsfor small items.  
They can easilyslide in tothe tub andmay damage thetub.  
Pre-treat all stainsand heavily soiledareas for bestresults.  
Do not overloadyour washer.  
When loading wetitems,keep water levelhigh enough so items  
can float easilyin the water.  
Close the doorproperly after loadingthe clothes.if youkeep the  
lid up,the washerwill not start.  
Proper Use of Detergent:  
It is goodwashing practice toadd the detergentto the water  
before you addthe clothes sothat the detergentcan work  
effectively on yourclothes.  
Notes: You can less ormore detergent dependingon the sizeof  
the load,water typein your livingarea,whether it issoft  
or hard and whether the clothesare heavily soiledor  
lightly soiled.  
Bleach Dispenser:  
Bleach dispenser islocated on frontcorner under theloading  
door.  
Pour in recommendedamount of bleachinto dispenser during  
the first washfill.  
7
 
Note:Use only liquid bleach in dispenser.  
Warning: Be careful notto spill undilutedbleach on thewasher  
cabinet or yourclothes.As it isa storng chemical,it  
maydamage some ofyour clothes or the finish ofthe  
washer if notproperly diluted.  
Use the manufacturers chart,on productcontainer  
for recommended useof liquid orpowder bleach.  
Softener inlet  
Softener  
inlet  
SOFTENER  
Please follow softener instructions for dose usage.  
Before washing put the softener into the filling entrance(can be  
found on the balancing ring by rotating the inner tub, as illustrated  
in the drawing).  
Try to avoid adding softener in, if you do not intend to wash  
immediately. The softener may harden and may cause a poor flow.  
Please do not use softener in the following cases Selected rinsing  
times more than two; Choosing rinse/spin two-in-one program.  
Normal Operating Sounds  
The following soundsare normally heardduring the operation  
Of the washer:  
Tumbling sounds:This is normalas the heavywet clothes in  
The washer arecontinuously being lossedaround.  
Air rushing noise: This happenswhen the washertub spins at  
Very high spining speed.  
Wash and Rinse cycles goingon and offwill also makeclicking  
Sounds.  
8
 
Lint Filter  
The lint filter must be used during washing.  
It must be cleaned after each wash.  
Install  
Take off the lint filter.  
1
2
3
Clean out thelint in thefilter.  
Install the lint filter.  
Take off  
Take off  
Install the inner cover  
(To prevent water spillagefrom tub)  
1.Open the top lid of the washing machine.  
Install  
2.Put the inner cover component on the outer tub cover, lining up  
the inner cover shaft to the installation hole of the corresponding  
outer tub cover shaft groove.  
3.Firstly insert the inner cover shaft of one side into the corresponding  
outer tub cover shaft groove, then push the other inner cover  
shaft into the corresponding outer tub cover shaft groove. Please  
install in the designated position to guarantee there is no abnormal  
sound in opening and closing of the inner cover, and the operation  
shall be smooth. Do not remove the inner cover component after  
washing.  
Outer tub cover  
Section I enlarging  
Outer tub cover  
shaft groove  
Inner cover shaft  
Inner cover  
Push  
9
 
CARE AND CLEANING GUIDE  
Warning: Always unplug your washer to avoid electric shock before  
cleaning. Ignoring this warning may result in injury. Before using  
cleaning products, always read and follow manufacturer  
warnings to avoid personal Injury or product damage.  
Cleaning and Maintenance  
Use only damp or sudsy cloth for cleaning control panel.  
To avoid any kind of damage to cabinet finish, wipe washer cabinet as  
needed. If you spill liquid/powdered softener bleach or detergent on  
the cabinet, wipe cabinet immediately because it can damage the  
finish.  
Do not use any abrasive, harsh chemicals, ammonia, chlorine bleach,  
concentrated detergent, solvents or metal scouring pads. Some of  
these chemicals may dissolve, damage and/or discolor your washer.  
Remove pins or other sharp objects from clothes to prevent scratching  
of interior parts.  
Leave lid open after you are done washing to allow inside of washer  
to dry and prevent bad odors.  
Moving & Vacationing  
Turn off water supply faucet's and disconnect hoses. Drain water from  
all hoses.This will prevent from damaging due to water leakage if the  
hoses accidentally get ruptured or they become loose.  
Disconnect electrical plug.  
Dry inner wash tub. If moving washer disconnect drain hose.  
Turn the leveling legs clockwise all the way in.  
.
Move and store your washer in upright position only  
To prevent mold or mildew, leave lid open so moisture inside machine  
can evaporate.  
10  
 
Storage of Your Washer  
The washer must be stored at room temperature.  
If you just got delivery of a washer when outside temperature is below  
freezing,do not operate until washer has warmed to room temperature.  
Do not install or operate your washer where room temperature is  
below freezing.  
11  
 
TROUBLE SHOOTING  
Washer does not operate:  
Check if unit is plugged in. The plug may have come loose.  
Check if the electrical wall receptacle is of proper voltage.  
Check if the circuit breaker needs to be reset or if the fuse need to be  
replaced.  
Check if the washer is overloaded :load may need to be re-balanced  
and clothes may need to be redistributed.  
Check if the lid is open. You may have to close the lid properly.  
The washer pauses in some cycles. This is normal in delicate or  
hand-wash cycle which has short period of time. You will not hear  
washer operation for a short period of time . When the soak time is  
over, it will start automatically.  
Problems with water:  
Not enough water coming out: Water faucet may need to be turned  
on fully water . Hoses may be tangled or wrinkled up. Straighten out  
hoses. Check water level selection, it may need to be readjusted.  
Water temperature is incorrect: Check your water heater temperature.  
Hot water needs to be at a temperature of at least 120 F-140 F(49 C  
-60 C).Check to make sure the inlet hoses are properly connected.  
(E.g. Hot to hot & cold to cold)  
Water leaks: This is due to not properly installing drain hose or  
fill hoses. Your home drain may be clogged . You may need to tighten  
hoses, check the plumbing or call a plumber.  
Water will not drain: This is due to not installing your drain hose  
properly. Check theposition of the drain hose. In order to drain  
properly, make sure that top of drain outlet is less than 5 ft. (1.5 m)  
above the floor.  
Washer is making noise:  
Washer may need to be reinstalled. (Check washer installation  
section)  
12  
 
Washer load may need to be re-balanced, as the load may be uneven.  
Coins, loose change, buttons or other heavy objects could make  
noise(read Operating Guide-Normal Operating Sounds).  
Squealing sound: Due to overloaded wash tub.  
Vibration Noise: Due to not leveling washer properly on the floor and  
uneven distribution of clothes in the tub.  
Problems with clothes:  
Clothes are too wrinkled: this is due to improper sorting, overloading  
and washing in too hot water repeatedly.Avoid overloading and resort  
your load. Do not mix heavy clothes such as work clothes with light  
clothes such as blouses, light shirts and delicate items. You may need  
to wash in warm or cold water  
Have soap residue: detergent may not be dissolving in water.  
Check water temperature or you need to add detergent as wash  
tub is being filled with water.  
Spots or stains on your clothes: this is due to incorrect use of fabric  
softener. You may need to read proper instructions on the container  
and follow proper directions when using the softener.  
Clothes are grayed or yellowed: this is due to not pouring enough  
detergent for large loads. You may have to add more detergent to the  
load.  
Clothes are ripped & have holes/excessive wear & tear: this is due to  
sharp objects such as pins and belt buckles left in pockets. You will  
need to remove small loose sharp objects. Fasten belts, zippers,  
metal snaps etc. Check if you are using undiluted bleach. Never add  
undiluted bleach to wash.  
Note:  
Trouble Codes  
Reason  
E0  
E1  
E2  
E4  
Top lid not closed during delay start sequence  
Blockage of drain hose  
Top lid not closed during wash operation  
The water inlet time exceeds the preset time  
(30minutes)  
The communication is bad  
E7  
F2  
The protection ofwater overflow  
13  
 
INSTALLATION INSTRUCTIONS  
Tools and Materials Required  
You will need to have following tools to help  
you with theinstallation of yourwasher:  
Pliers  
Wrench  
TapeMeasure  
Gloves  
Level  
Accessories Supplied  
Quantity  
1.Hot & Cold inlet hoses  
2.Drain Hose Hook  
3.Pipe Hoop  
2
1
1
1
4.Inner Tub Cover  
5.Outer Drain Hose  
1
2
1
3
4
5
14  
 
Unpacking Your Washer  
Remove all packing materials. This Includes the foam base and all  
.
adhesive tape holding the washer accessories inside and outside  
Open the top lid to remove the styrofoam drum brace. Pull to remove.  
Before using this washing machine,  
please remove this shipping bar by  
pulling handle and dispose it  
properly, otherwise the washing  
machine will be damaged.  
Pull out  
Shipping bar  
Leveling Your Washer  
Your washer has 4 leveling legs; which are located on the  
bottom corners. After properly placing your washer in its final  
position, you canlevel your washer.  
Leveling legs can be adjusted by turning them counter clockwise  
to raise your washer or turning them clockwise to lower your  
washer.  
Adjustable foot  
High  
Low  
Warning: Leveling of washer is very important to prevent  
vibration during spin.  
15  
 
Steps for Installation  
Select a away suitable location for the washer on a hard even surface  
from direct sunlight or heat source e.g. radiators, base board heaters,  
cooking appliances etc.Any floor unevenness should be corrected with  
the leveling legs located on the bottom corners of the washer.The  
washer must be placed at room temperature.You must not place washer  
where the temperature is at below freezing.  
Installing Your Washer:  
Read through these instructions carefully before installation.  
1. Connect the hot and cold water inlet hoses to the hot and cold water  
faucet.  
2. Connect the other end to the corresponding washer inlet located at the  
back of machine.  
Cold water inlet hose  
Hot water inlet hose  
Note: You may have to use pliers to tighten the coupling. Do not over tighten  
because you may cause damage to the valve.  
You should use the new hose-sets supplied with the washer. Old  
hose-sets should not be reused.  
16  
 
4. Install the drain hose to the side of the washer using the drain hose  
damp provided. The drain hose must be placed into a drain pipe or sink  
at least 1 1/2inches in diameter. Use the goose neck to the hose in  
place. To avoid possible water back up, the drain hose must reach a  
minimum height of 1000mm and a maximum height of 1500mm.  
Water Supply Hose  
Water Inlet  
Goose Neck  
Hose Bend  
Drain Hose  
5.Plug the washer into a regular 220-240Volt/50Hz,10Amps outlet.  
Note :Carefully inspect all around the machine and at the back for any  
leaks, and tighten any loose connections.  
Caution:If, after completing these steps, you are unsure that unit is  
properly installed, contact a qualified installer.To ensure that  
your washer is properly installed, it is recommended that it  
be installed by a certified installer.  
17  
 
ELECTRICAL REQUIREMENTS  
Grounding Instructions  
This appliance must be grounded. In the event of an electrical short  
circuit, grounding reduces the risk of electric shock by providing an  
escape wire for the electric current. This appliance is equipped with a  
cord having a grounding wire with a grounded plug. The plug must be  
inserted into an outlet that is properly installed and grounded.  
Improper use of the plug can result in a risk of electric shock.  
Consult a qualified electrician or service person if the grounding  
instructions are not completely understood or if doubt exists as  
to whether the appliance is properly grounded.  
Wiring Requirements:  
The washer must be plugged into at least 10AMP 220-240 VOL,  
50 HZ GROUNDED OUTLET.  
T
Note: Where a standard two-prong  
outlet is encountered,  
it is the personal responsibility  
and obligation of the  
consumer to have it replaced  
with a properly grounded  
three-prong outlet.  
Extension Cords:  
We do not recommend that you use an extension cord.  
Power Interruptions  
Occasionally there may be power interruptions due to thunderstorms or  
other causes. Remove the power cord from AC outlet when a power  
outage occurs. When power has been restored re-plug power cord to AC  
outlet. If outage is for a prolonged period, clean washer before using it  
again.  
18  
 
SPECIFICATION  
Rated voltage frequency  
Rated washing / spinning capacity  
Spin speed max  
220-240V~ 50Hz  
9.0kg  
700rpm  
Water level/Water quantity (about L) 1/28 2/36 3/49 4/54 5/61  
6/67 7/73 8/79 9/89 10/95  
Max water consumption  
Injection pressure  
Weight(approx)  
About 122L(Normal program)  
0.03MPa-1.0MPa  
79kg  
 

Graco Ventilation Hood 77X540 User Manual
Hamilton Beach Toaster 840119200 User Manual
HANNspree Flat Panel Television ST03 15U1 User Manual
Heath Zenith Home Security System SL 5330 User Manual
Hotpoint Cooktop 6511 User Manual
Hotpoint Microwave Oven RVM1625 User Manual
Humax DVR IHDR 5200C User Manual
Humminbird Fishing Equipment Fishing Equipment User Manual
I Data Portable Media Storage FS 250 User Manual
Impex Home Gym SB 208 User Manual